超聲波清洗機包含單槽超聲波清洗機、非標超聲波清洗機、標準型超聲波清洗機、循環過濾超聲波清洗機、噴絲板超聲波清洗機等。

　　Ultrasonic cleaning machines include single slot ultrasonic cleaning machines, non-standard ultrasonic cleaning machines, standard ultrasonic cleaning machines, circulating filtration ultrasonic cleaning machines, and spinneret ultrasonic cleaning machines.

　　超聲波清洗機的主要參數

　　Main parameters of ultrasonic cleaning machine

　　超聲波清洗是基於空化作用，即在清洗液中無數氣泡快速形成并迅速內爆。由此產生的沖擊將浸沒在清洗液中的工件內外表面的污物剝落下來。隨著超聲頻率的提高，氣泡數量增加而爆破沖擊力減弱，因此，高頻超聲特別適用於小顆粒污垢的清洗而不破環其工件表面。氣泡是在液體中施加高頻（超聲頻率）、高強度的聲波而產生的。因此，任何超聲清洗系統都具備三個基本元件：盛放清洗液的槽、將電能轉化為機械能的換能器以及產生高頻電信號的超聲波發生器。

　　Ultrasonic cleaning is based on cavitation, where numerous bubbles rapidly form and implode in the cleaning solution. The resulting impact will peel off the dirt on the inner and outer surfaces of the workpiece immersed in the cleaning solution. With the increase of ultrasonic frequency, the number of bubbles increases and the blasting impact force weakens. Therefore, high-frequency ultrasound is particularly suitable for cleaning small particle dirt without damaging the surface of the workpiece. Bubbles are generated by applying high-frequency (ultrasonic frequency) and high-intensity sound waves to liquids. Therefore, any ultrasonic cleaning system has three basic components: a tank for holding cleaning solution, a transducer for converting electrical energy into mechanical energy, and an ultrasonic generator for generating high-frequency electrical signals.

　　(1)頻率：≥20KHz ，可以分為低頻，中頻，高頻3段。

　　(1) Frequency: ≥ 20KHz, can be divided into three bands: low frequency, medium frequency, and high frequency.

　　(2)清洗介質：采用超聲波清洗，一般兩類清洗劑：化學溶劑、水基清洗劑等。清洗介質的化學作用，可以加速超聲波清洗效果，超聲波清洗是物理作用，兩種作用相結合，以對物件進行充分的清洗。

　　(2) Cleaning medium: Ultrasonic cleaning is used, generally two types of cleaning agents: chemical solvents, water-based cleaning agents, etc. The chemical action of cleaning media can accelerate the ultrasonic cleaning effect. Ultrasonic cleaning is a physical action that combines the two to thoroughly clean objects.

　　(3)功率密度：功率密度=發射功率（W）/發射面積（cm2）通常≥0.3W/cm2，超聲波的功率密度越高，空化效果越強，速度越快，清洗效果越好。但對于表面光潔度甚高的物件，采用長時間的高功率密度清洗會對物件表面產生“空化”腐蝕。

　　(3) Power density: Power density=emission power (W)/emission area (cm2) is usually ≥ 0.3W/cm2. The higher the power density of ultrasound, the stronger the cavitation effect, the faster the speed, and the better the cleaning effect. However, for objects with high surface smoothness, prolonged high-power density cleaning can cause "cavitation" corrosion on the surface of the object.

　　(4)超聲波頻率：超聲波頻率越低，在液體中產生的空化越容易，產生的力度大，作用也越強，適用于工件（粗、臟）初洗。頻率高則超聲波方向性強，適用于精細的物件清洗。

　　(4) Ultrasonic frequency: The lower the ultrasonic frequency, the easier cavitation is generated in the liquid, the greater the force generated, and the stronger the effect. It is suitable for initial cleaning of workpieces (coarse, dirty). High frequency results in strong directionality of ultrasonic waves, suitable for fine object cleaning.

　　(5)清洗溫度：一般來說，超聲波在30℃-40℃時的空化效果好。清洗劑則溫度越高，作用越顯著。通常實際應用超聲波時，采用50℃-70℃的工作溫度。

　　(5) Cleaning temperature: Generally speaking, ultrasonic waves have a good cavitation effect at 30 ℃ -40 ℃. The higher the temperature, the more significant the effect of the cleaning agent. Usually, when applying ultrasound in practice, a working temperature of 50 ℃ -70 ℃ is used.

　　超聲波清洗機使用注意事項：

　　Precautions for using ultrasonic cleaning machine:

　　(1)超聲波清洗機電源及電熱器電源有良好接地裝置。

　　(1) The power supply of the ultrasonic cleaning machine and the electric heater have good grounding devices.

　　(2)超聲波清洗機嚴禁無清洗液開機，即清洗缸沒有加一定數量的清洗液，不得合超聲波開關。

　　(2) It is strictly prohibited to start the ultrasonic cleaning machine without cleaning solution, that is, the ultrasonic switch cannot be turned on without adding a certain amount of cleaning solution to the cleaning tank.

　　(3)有加熱設備的清洗設備嚴禁無液時打開加熱開關。

　　(3) Cleaning equipment with heating devices is strictly prohibited from turning on the heating switch when there is no liquid.

　　(4)禁止用重物(鐵件)撞擊清洗缸缸底，以免能量轉換器晶片受損。

　　(4) Do not hit the bottom of the cleaning cylinder with heavy objects (iron parts) to prevent damage to the energy converter chip.

　　(5)超聲波發生器電源應單獨使用一路220V/50Hz電源并配裝2000W以上穩壓器。

　　(5) The ultrasonic generator power supply should use a separate 220V/50Hz power supply and be equipped with a voltage regulator of 2000W or above.

　　(6)清洗缸缸底要定期沖洗，不得有過多的雜物或污垢。

　　(6) The bottom of the cleaning cylinder should be regularly flushed to prevent excessive debris or dirt.

　　(7)每次換新液時，待超聲波起動后，方可洗件。

　　(7) When changing the liquid each time, wait for the ultrasonic wave to start before washing the parts.

　　以上就是我們產品的相關介紹，本文來源 超聲波清洗機， 更多精彩內容請點擊：http://baobaoqu.cn

　　The above is the relevant introduction of our product. This article is from the ultrasonic cleaning machine. For more exciting content, please click: http://baobaoqu.cn